Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Bensonhurst Homeowners
A missing cap or a cracked crown turns a small chimney problem into a water problem. Rain runs straight down the flue, mortar softens, and the next freeze splits it wider. That’s the cycle we stop. Our technicians have up to 12 years of experience fitting caps and rebuilding crowns on the brick chimneys common across Bensonhurst, from the two-family semis off 18th Avenue to the detached houses near Bensonhurst Park. We work with trade-grade components from HeatShield, Gelco, Olympia Chimney and Famco, matched to the flue rather than pulled off a hardware shelf. Same-day service is often possible when you call early. Call (855) 924-3713 for a free, no-obligation estimate. We answer 24/7.
What Our Chimney Cap & Crown Service Includes
Cap Installation
A cap is the metal or stainless hood that sits on top of the flue and keeps rain, birds, squirrels and wind-driven debris out while letting smoke escape. If your chimney has no cap at all, that open flue is collecting water every storm and offering wildlife a way in. We measure the flue, choose a cap that fits the crown without blocking draft, and secure it so a nor’easter won’t shift it.

Cap Replacement
Caps rust through, warp, or lose their mesh when the wrong metal was used or the fasteners have pulled loose. Once the screen has holes, animals get in and sparks can land on the roof. We remove the old cap, check the flue tile beneath it for damage, and fit a replacement sized and anchored for that chimney.

Crown Repair
The crown is the concrete or mortar slab at the very top of the chimney that sheds water away from the brick. Hairline cracks widen as water gets in and freezes, and a failed crown is one of the most common sources of a slow leak into a Bensonhurst attic. We rebuild or patch the crown with the correct slope so water runs off the way it should.

Crown Coating
Crown coating is a flexible, weatherproof membrane applied over a crown that’s cracked but still structurally sound. It’s the right call when the slab has surface fractures but hasn’t started breaking apart, and it seals those fractures before another winter makes them worse. We clean and prep the surface first so the coating bonds instead of peeling.
Multi-Flue Cap
A multi-flue cap is a single larger housing that covers two or more flues side by side, common on the larger brick chimneys around Bensonhurst. It protects every flue at once and gives a cleaner look than several separate caps on one stack. We build these to the exact footprint of your chimney so each flue still draws correctly.
Custom Cap
Some chimneys have an unusual size, an oval flue, or a shape no stock cap fits. A custom cap is fabricated to your chimney’s dimensions so it seats properly and doesn’t rattle or leak at the edges. We take the measurements on site and specify the material to suit the venting setup.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We specify HeatShield where the flue walls themselves need attention, because their ceramic resurfacing system lets us restore a deteriorating liner rather than jump straight to full relining. On the crown side, Gelco crown repair products hold up to the freeze-thaw swings that work on masonry here, and they bond to the existing concrete instead of sitting on top of it like a cosmetic patch.
Olympia Chimney and Famco supply the caps and components we fit most often, and we choose between them based on the flue size, the number of flues on the stack, and how the cap needs to anchor to your crown. Different configurations call for different parts, so we don’t default to one size for every roof. Whether you have Olympia Chimney, Famco or any other make already on your chimney, we can help.
Signs You Need Chimney Cap & Crown Right Now
- No cap on the flue: An open flue takes in rain directly, and water is the leading cause of chimney masonry failure. It also lets birds and squirrels nest inside, which blocks draft.
- Visible cracks in the crown: Cracks you can see from the ground are usually bigger up close, and each freeze-and-thaw cycle widens them. Water follows those cracks into the brick and eventually into the house.
- Rust or holes in the cap mesh: Once the screen fails, debris and animals get in and sparks can reach the roof. If the metal itself is flaking, it’s past the point of a simple screen replacement.
- Water stains on the ceiling near the chimney: Staining often traces back to a cracked crown or an unsealed cap edge, not the roof. Finding the source early keeps the repair small.
- Crumbling mortar at the chimney top: Soft or missing mortar at the crown level means water has been getting in for a while. A crown rebuild now is far less work than rebuilding the top courses of brick later.
Our Chimney Cap & Crown Process – Step by Step
- 1
Inspection first. We look at the crown, the flue tiles, the cap and the brick below the crown line before recommending anything. A camera inspection lets us see the inside of the flue, and you get the photos so you can see what we see.
- 2
Clear diagnosis. We tell you what’s actually wrong, what’s cosmetic, and what can safely wait until next season. You won’t be told you need a full reline if the evidence doesn’t support it.
- 3
Material selection. Based on the flue size, the number of flues and the condition of the crown, we specify the cap or repair material. We explain why that particular component fits your chimney.
- 4
The work. We remove the old cap or crown material, prep the surface, and install the replacement. Safety comes first on any roof work: height, ladders and steep pitches are a job for trained technicians, not a weekend project.
- 5
Final check and photo report. We confirm the cap is secure, the crown slopes correctly, and the flue still draws. You get a photo record of the finished work and a written summary of what was done.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Bensonhurst?
A single-flue cap installation in Bensonhurst typically runs $200 to $450 depending on cap material and flue size. A multi-flue or custom cap generally falls in the $400 to $900 range, since it’s built to the footprint of the stack. Crown repair usually runs $350 to $800, and a full crown rebuild runs higher, from about $700 to $1,500, because the old slab has to come off and be re-poured with the correct slope. Crown coating sits at the lower end, typically $250 to $600.
What moves the price: the number of flues, the height and pitch of the roof, whether the old crown needs full removal, and the material you choose for the cap. Stainless lasts longer than galvanized and costs more up front.
How to avoid overpaying: get the written scope before any work starts, ask whether the crown needs repair or full replacement, and ask to see the photos. A flat-price sweep agreed before booking, a camera inspection with a photo report, and a satisfaction guarantee belong in a fair estimate. Everything we recommend is backed by camera evidence you can look at yourself, and we say plainly when a repair can wait. The written estimate sets the final price, and it’s free.
Chimney Cap & Crown Near Bensonhurst – Our Service Area
From Bensonhurst we also work in the surrounding neighborhoods, including Gravesend, Dyker Heights, Midwood, Borough Park, Bay Ridge, Sheepshead Bay, Kensington and Sunset Park. Roof access and chimney design vary block to block, so local knowledge matters more than a generic quote. If you’re nearby, we can schedule a visit that fits your week. Read more about chimney cap & crown work nearby, or see our Chimney Sweep Bensonhurst page for the full range of services.
Serving Bensonhurst, NY – Our Local Coverage Area
We serve Bensonhurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Bensonhurst
A chimney cap is the metal hood and mesh that sits on top of the flue, and the crown is the concrete or mortar slab at the top of the chimney that sheds water away from the brick. The cap keeps rain, animals and debris out of the flue; the crown protects the masonry itself from water damage. Together they’re the first line of defense against the water intrusion that ruins chimneys. Call (855) 924-3713 to have both checked.
A standard single-flue cap installation usually takes under an hour once we’re on site, and a crown repair is typically a same-day job. A full crown rebuild takes longer because the old slab has to be removed and new material has to set properly. We’ll give you a realistic time estimate before we start. Call (855) 924-3713 to book an assessment.
Cap installation typically runs $200 to $450 for a single flue, crown repair usually runs $350 to $800, and a full rebuild sits higher. Custom and multi-flue caps are priced to the size of the stack. The written estimate sets the final price, so you’ll know the number before we touch the roof. Call (855) 924-3713 for an exact quote, and estimates are free.
Yes. We fit and service Olympia Chimney and Famco caps and components, and we choose between supply lines based on your flue size and stack configuration. We also work with HeatShield and Gelco for flue and crown restoration. If your existing cap is another make, we can still help.
Same-day service is often possible when you call early in the day. Call (855) 924-3713. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Yes. Every cap and crown job is backed by a satisfaction guarantee, and we leave you with photos of the finished work plus a written summary. If something isn’t right after the job, we come back. Call (855) 924-3713 with any questions about the guarantee.
You don’t need to do much. Clear access to the fireplace and, if applicable, the roof hatch or attic entry, and let us know about any pets or parking restrictions. We’ll handle the rest, including cleanup. Call (855) 924-3713 to schedule.
For related work in the area, see our chimney cap & crown page and our chimney repair service. If you also need the flue cleaned, our chimney sweep and chimney inspection pages cover the details, along with fireplace repair.
Schedule Your Chimney Cap & Crown Service in Bensonhurst Today
Don’t let another storm pour water down an open flue. Call (855) 924-3713 for a free, no-obligation estimate on a cap, crown repair, or a full custom cap built for your chimney. We’ll inspect first, show you the photos, and tell you honestly what can wait. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Bensonhurst.