Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Bensonhurst Homeowners
Brick that crumbles when you touch it, a white stain spreading down the chimney breast, or a rusty streak on the flashing where water gets in: these are the problems that bring people to a chimney repair specialist, and they don’t fix themselves. Your chimney is a venting system, and every crack in the mortar joints or crown is a path for water and a weak point in the draft. Our technicians have up to 12 years of experience reading exactly this kind of damage, and we handle the whole scope, from mortar work and waterproofing to relining with DuraFlex. Estimates are free and the price is set per job by the written estimate. Call (855) 924-3713. We answer 24/7.
What Our Chimney Repair Service Includes
Chimney repair in Bensonhurst covers the masonry, the metal, and the liner: the parts of the venting system that carry smoke out and keep weather from coming in. Here is what each piece of the work involves and when it’s needed.
Mortar Repointing
Repointing is raking out failed mortar between bricks and pressing in fresh, correctly mixed mortar to the full depth of the joint. You need it when joints have gone sandy, cracked, or recessed far back from the brick face, which lets water into the wall. We match the mortar mix to the brick and the era of the building rather than defaulting to a hard cement that traps moisture, and we repoint chimney stacks and the joints above the roofline where freeze-thaw does the most damage.

Spalling Brick Repair
Spalling is when a brick face flakes, peels, or pops off, usually because trapped moisture froze inside the brick and pushed outward. It shows up as piles of brick fragments on the roof or in the yard and as faces that look scooped out. We replace spalled units with brick matched to the surrounding course and correct the moisture source behind the failure, since replacing brick without fixing the cause just puts a new face on the same problem.

Chimney Waterproofing
Waterproofing is a breathable treatment applied to the masonry so rain runs off while vapor inside the chimney can still escape. It’s worth doing when the brick absorbs water quickly, when the stack stays damp long after rain, or right after repointing or rebuilding work. We apply a vapor-permeable sealer to the stack, not a film-forming coating that seals moisture in, and we waterproof the crown and the masonry together so one weak point doesn’t undo the other.

Flashing Repair
Flashing is the metal where the chimney meets the roof, stepped into the brick and lapped over the shingles to shed water away from the junction. It’s the culprit when you see rust streaks, stained ceiling plaster near the chimney, or daylight at the seam. We reset or replace failed flashing and seal the counter-flashing into the masonry so the roof-chimney joint stays watertight through the freeze-thaw cycles that work it loose.
Chimney Rebuilding
Rebuilding is for a stack that’s gone past repair at the top: leaning courses, loose bricks, or a crown and upper flue that can’t be stabilized with spot work. You need it when the top several courses have lost their bond and no amount of tuckpointing will hold them. We take the stack down to sound masonry, rebuild with new brick and mortar, and set a proper crown, working to the structure’s needs rather than a patch that will fail again next season.
Tuckpointing
Tuckpointing is the finer end of joint work: cutting out deteriorated mortar and refilling the joint with a neat, finished profile that suits the brick. It’s needed on historic or decorative masonry where the joint itself is part of the look and a rough repoint would stand out. We size and finish the joints to match the original detail and point up damaged areas rather than masking them, so the repaired section blends with the rest of the stack.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
Most of the repair work that comes up is on materials with a known name behind them, and knowing how those products wear is half the diagnosis. HeatShield is a ceramic flue-resurfacing system for liner walls that have started to deteriorate, and we apply it in cases where the flue can be restored rather than fully relined. It’s a specialist method, and understanding where the ceramic coating bonds reliably is what separates a lasting resurface from a temporary fix. When a full reline is the right call instead, we install DuraFlex flexible liner systems, and we know where that liner is stressed at the top and the turn into the smoke chamber.
Gelco and Olympia Chimney components come up on the cap, crown, and connector side, and we work with them because the fit and the heat resistance match what a residential flue actually sees. Famco parts round out the mix for the chimneys that don’t fall neatly into one product family. Because we draw from several professional supply lines, we match the component to the chimney’s specific configuration rather than forcing one brand onto every job. Whether you have HeatShield on the liner, DuraFlex, or any other make, we can help.
Signs You Need Chimney Repair Right Now
Some chimney damage can safely wait through the season. Other damage is a safety matter and should be looked at before you light another fire. These are the signs that put a chimney in the second group.
- Crumbling or sandy mortar joints. When joints powder away between the bricks, the stack is losing its structural bond and letting water in. Left alone, the deterioration reaches the brick itself and turns a repoint into a rebuild.
- Flaking or hollow-sounding brick faces. Spalled brick means water is getting trapped and freezing inside the masonry. Each freeze-thaw cycle widens the damage, so catching it early keeps it to a few replaced units instead of a rebuilt top.
- White staining or dark damp patches on the masonry. Efflorescence and persistent damp point to water moving through the brick rather than around it. That’s the signal to waterproof and to check the crown and flashing before the interior of the house gets wet.
- Rust streaks or ceiling stains near the chimney. This usually traces to failed flashing at the roof junction. Water following the flashing into the roof deck can do hidden damage to framing long before it shows on the ceiling.
- A damaged crown or a leaning stack. A cracked crown lets water down into the flue structure, and any real lean in the stack points to a bond failure lower down. Both call for a proper look before the next burn, since a compromised chimney can let combustion gases into the house.
Our Chimney Repair Process – Step by Step
Repair work on a chimney is only as good as the diagnosis behind it, so the process starts with looking carefully and explaining what we find before anyone picks up a trowel.
- 1
Inspection and photos. We examine the stack, crown, flashing, and flue, and take photos of what we see. You get to see the same damage we do, so nothing gets recommended that you can’t verify for yourself.
- 2
Camera look inside the flue. A video camera run inside the liner shows the condition of the flue walls, joints, and any gaps that aren’t visible from outside. This is where we confirm whether the liner needs resurfacing, relining, or nothing at all yet.
- 3
A written scope and flat price. We lay out exactly what the work covers, which materials we’ll use, and the price, and you agree to it before we book the job. If part of the repair can safely wait, we tell you so plainly.
- 4
The repair itself. Repointing, brick replacement, flashing, crown work, waterproofing, or a reline with DuraFlex or a HeatShield resurface, done in the order that protects the finished work. We protect the roof and the surrounding area and clean up as we go.
- 5
Final check and report. We confirm the repair holds, photograph the finished work, and give you a report on the chimney’s condition. You leave with a clear record of what was done and what to watch going forward.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Bensonhurst?
Chimney repair in Bensonhurst typically runs from a few hundred dollars for spot work like flashing or a section repoint up into the low thousands for a rebuild of the upper stack or a full reline, depending on how far the damage reaches. Brick rowhouses here sit close together and their chimneys take a beating from the damp and freeze-thaw swings of a New York winter, so the extent of the masonry that’s failed is the biggest factor. Height and roof access, how many courses need replacing, and whether the flue also needs resurfacing all move the number.
- Mortar repointing: priced by the linear foot of joint and the height of the stack.
- Spalling brick: priced by the number of units replaced plus the moisture fix behind them.
- Waterproofing: priced by the size of the masonry surface treated.
- Flashing repair: priced by the length of the joint and whether metal is reset or replaced.
- Rebuilding and liner work: the higher end, priced per the courses removed or the length of liner installed.
The way to avoid overpaying is to insist on camera evidence before anyone recommends liner or masonry work, and to get the flat price in writing before booking. Our estimates are free, they include the inspection and photo report, and the written estimate sets the final price. Call (855) 924-3713 for an exact quote on your chimney.
Chimney Repair Near Bensonhurst – Our Service Area
We connect homeowners across this part of Brooklyn with vetted local professionals, and from Bensonhurst that reaches Gravesend, Dyker Heights, Midwood, Borough Park, Bay Ridge, and Sunset Park, along with Sheepshead Bay, Coney Island, Kensington, Flatlands, and Brighton Beach. Response depends on the job and the schedule, and a sweep or repair visit is booked rather than dispatched on the spot. For related masonry work in a neighboring area, see our chimney repair page, and for a broader look at the whole chimney service, our Chimney Sweep Bensonhurst page covers cleaning and inspection.
Serving Bensonhurst, NY – Our Local Coverage Area
We serve Bensonhurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Bensonhurst
Chimney repair is fixing the parts of the venting system that have failed: the mortar, brick, crown, flashing, waterproofing, and liner. It’s the work that keeps the chimney structurally sound and keeps combustion gases and water where they belong. It covers everything from a spot repoint to a full rebuild or reline, and we handle all of it in one relationship so you’re not bounced between a sweep and a mason.
A flashing repair or a section of repointing can be done in a single visit, while a full repoint, waterproofing, or reline usually takes more than one, and a rebuild of the upper stack runs longer still. The scope and the weather drive the timeline. Your written estimate tells you the expected time for your specific job before we start. Call (855) 924-3713 to book an inspection and get a realistic timeline.
It depends on the extent of the damage: spot flashing and small repoints sit at the low end, while a rebuild or a reline with DuraFlex or a HeatShield resurface reach into the thousands. The biggest cost driver is how much masonry has failed and how high the work goes. The written estimate sets the final price, and the estimate is free. Call (855) 924-3713 for an exact quote.
Yes. We apply HeatShield ceramic flue-resurfacing and we assess existing liners to decide whether a resurface will hold or whether a full reline is the honest answer. It’s a specialist method most basic sweep companies aren’t equipped for, so it’s worth asking specifically when your liner walls are deteriorating. Call (855) 924-3713 and we’ll look at the flue with a camera to tell you which path makes sense.
Same-day service is possible depending on the schedule. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening. Call (855) 924-3713 to check same-day availability for your repair.
Yes, our repair work carries a satisfaction guarantee, and the flat price and materials are spelled out in the written estimate before we book. You’ll have the camera inspection and photo report showing what was found and what was done. If something isn’t right after the repair, we stand behind the work.
Clear access to the fireplace and the hearth, and let us know about any pets or anything fragile in the room. If the job involves roof or stack work, we’ll tell you in advance what access we need. Beyond that, there’s nothing to do: we bring the tools and the materials, and you get the inspection and a clear report of what we find.
Schedule Your Chimney Repair Service in Bensonhurst Today
A crumbling stack or a leaking flashing gets worse with every freeze and every storm, so it’s worth settling now, before burning season. Call (855) 924-3713 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday, and we’ll show you the camera evidence before recommending a single dollar of work. Our technicians have up to 12 years of experience with chimney repair and the surrounding work, from chimney repair in Dyker Heights to masonry and chimney cap and crown service, so one call covers the whole chimney.
Written by the team at Chimney Sweep Bensonhurst.